Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
The writer is making a number of great points on Tools You Need to Install a New Bathtub as a whole in this post directly below.
Setting up a bath tub isn't precisely rocket science, however it does need solid plumbing, carpentry, and also in some cases, tiling abilities. Changing an old bath tub with a new one is also a reasonably hard job. If the old bathtub is readily obtainable, the task can relocate speedily; if you need to open up a wall to remove the old bathtub and place the new bath tub, the job is much harder. In either instance, the task is within a home handyman's abilities, although you will need a helper to leave the old bathtub and also embeded in the brand-new one. Ensure you have actually certified yourself for the job and also are comfortable trying it. As opposed to employing a service provider to take control of a halfway-completed job, it is much better to think about utilizing one prior to you begin. Possibilities are you may need a specialist plumber to make tube links.
This short article will certainly assist you install a brand-new tub in your washroom if you have currently purchased a brand-new tub as well as do not require to transform the arrangement of your previous water system pipelines.
Your devices as well as product checklist need to make up the following:
Preparing for the Setup
To start with, the sustaining frame supplied with the bath needs to be fitted (if required) according to the producer's directions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to make certain that if the tap comes with a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps unit to stop strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its last position.
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, after that the first thing you ought to do is detach the supply of water. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the limited access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will come from the pipes. Once the supply pipelines have been eliminated, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from turning during this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old securing compound.
Before moving on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new faucets to fit.
Setting up the Tub
Using the two wooden boards under its feet, position the bathtub in the needed position. The wood boards are valuable in equally spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto 4 little points.
The following objective is to ensure that the bathtub is leveled all round. This can be attained by checking the level as well as readjusting the feet on the bathtub till the spirit level checks out level.
To install faucets, fit all-time low of the outermost adaptable faucet adapter to the suitable supply pipe by making a compression join; then do the same for the other faucet.
Turn on the water supply as well as check all joints and also brand-new pipework for leaks and tighten them if required. Load the tub and also check the overflow electrical outlet and also the typical outlet for leakages.
Lastly, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and also sealing around the tub must wait until the bath tub has been used at least when as this will resolve it into its final placement.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic adapter to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washing machines are in area between the faucet as well as the sink. Safeguard the tap in place with the producer offered backnut. As soon as the faucet is safely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal tap connectors. The previous kind needs to be attached to the faucet ends initially, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture a rigid seal, creating the water to penetrate the wall surface in between the bathroom and the tiling, causing complications with dampness as well as feasible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and also installations. They are sold in tubes and cartridges, and also can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of soaked paper or soft rope. Remember to always fill the tub with water prior to sealing, to permit the activity experienced when the bathtub is in use. The sealant can split rather early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise quickly offered on the marketplace. It is suggested to fit the ceramic tiles using water-resistant or water resistant adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I stumbled upon that content on Installing A Bathtub while looking around the web. Sharing is good. Who knows, you might be helping someone out. We love reading our article about How to Install a Bathtub.
More Details Report this page